Do It Yourself Bath Setup.
Do It Yourself Bath Setup.
Blog Article
Right here in the next paragraph you might get more worthwhile insights pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bath tub isn't specifically rocket science, yet it does require strong plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is additionally a moderately hard task. If the old tub is easily easily accessible, the task can move rapidly; if you need to open up a wall to get rid of the old tub as well as place the brand-new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and also set in the new one. Make certain you have actually certified on your own for the work and are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to take into consideration employing one before you start. Chances are you may need an expert plumber to make tube links.
This write-up will help you set up a brand-new bath tub in your washroom if you have already bought a new tub and don't require to transform the setup of your previous water supply pipelines.
Your devices and also product list need to consist of the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited gain access to that is typically the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly come from the pipes. Once the supply pipes have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing compound.
Prior to carrying on to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin guaranteeing that the washing machines are in area in between the tap and also the sink. Protect the faucet in position with the manufacturer given backnut. When the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous kind ought to be attached to the tap finishes first, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Using both wooden boards under its feet, position the bathtub in the called for placement. The wooden boards are practical in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the tub till the spirit level checks out degree.
To set up faucets, fit the bottom of the furthest adaptable tap connector to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water as well as examine all joints and new pipework for leaks as well as tighten them if required. Fill up the bath tub as well as also check the overflow outlet as well as the regular electrical outlet for leakages.
Finally, repair the bath paneling as explained in the maker's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bath tub has actually been used a minimum of when as this will certainly resolve it into its final setting.
Getting ready for the Installment
To start with, the sustaining structure provided with the bathroom needs to be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets device to stop stress on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its final position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to break a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures and installations. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before securing, to allow for the motion experienced when the tub remains in use. The sealant can split fairly very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly readily available on the market. It is suggested to fit the floor tiles utilizing waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very inquisitive about A Step-by-Step Guide to Installing a Bathtub and I really hope you enjoyed reading the entire blog entry. In case you enjoyed reading our page please be sure to share it. I love reading our article about A Step-by-Step Guide to Installing a Bathtub.
Go Services Report this page